Product Sheet: A-B70/80-G Terminal Blocks ITOH DENKI Vietnam | ITOH DENKI Việt Nam

• I/O terminal on mounting bracket
• Available for XE / XP series
• Speed can be adjustable from 12.5% to 100% by potentiometer
• Built-in 10 kΩ resistor for speed variation
• Green LED illuminates for 24VDC power
• Red LED illuminates for motor error
• Reverse direction using a sliding switch
• 24VDC is supplied using cable splice connectors
• RUN & DIR inputs from any 24V DC switching source

Product Sheet: A-B70/80-G  Terminal Blocks ITOH DENKI Vietnam | ITOH DENKI Việt Nam 

Terminal Block No. E-920 Terminal Blocks ITOH DENKI Vietnam | ITOH DENKI Việt Nam 

Models Applicable

PM380AS, PM427AS

Terminal Blocks Document

Terminal Blocks Product Sheet

CAD Drawing Download (.DWG)

E-920 .DWG File

Features

• Standard accessory for PM380AS and PM427AS
• Please fix the output shaft by the special fitting. In case the output shaft runs freely, it causes the wires to break.
• The wiring method is the same as No. A-200.

Product Options:

Terminal Block No. A-800 Terminal Blocks ITOH DENKI Vietnam | ITOH DENKI Việt Nam 

Wiring time is drastically slashed.

Models Applicable

PM570AS, PM570BP, PM570AU,
PM605AS, PM605BP, PM605AU
PMT50AS

Terminal Blocks Document

Terminal Blocks Product Sheet

CAD Drawing Download (.DWG)

A-800 .DWG File

Advantages:

• It is not necessary to cut off or strip any wires.
• No terminal connection is required, which drastically slashes wiring time.
• No slack in wiring.

Order:

The fitting No. A-800 is an optional item and no Power Moller® is provided with this fitting as standard.

Please order it separately when ordering Power Mollers® and the No. A-800 will be delivered instead of No.
A-200 at an extra cost.

 

Dimensions

Product Options:

No. A-270-GS / A-280-GS Terminal Blocks ITOH DENKI Vietnam | ITOH DENKI Việt Nam

Terminal Block

No. A-270-GS / A-280-GS Terminal Blocks ITOH DENKI Vietnam | ITOH DENKI Việt Nam 

Model Applicable

PM486BS

The PM486BS is supplied with either the A-270-GS (flat on top) or the A-280-GS (point on top) terminal block to match the conveyor frame hole design.

Each output shaft should be fixed by the applicable fitting. In case output shaft turns freely it will cause the wires to break.

Terminal Blocks Document

Terminal Blocks Product Sheet

CAD Drawing Download (.DWG)

	A-270-GS .DWG File
	A-280-GS .DWG File

A-270-GS Hex Flat Up

A-280-GS Hex Point Up

Product Options:

Terminal Block No. A-200 Terminal Blocks ITOH DENKI Vietnam | ITOH DENKI Việt Nam 

Models Applicable

PM570AS, PM570BP, PM570AU,
PM605AS, PM605BP, PM605AU
PMT50AS

Terminal Blocks Document

Terminal Blocks Product Sheet

CAD Drawing Download (.DWG)

A-200 .DWG File

• Provided as a standard accessory for each applicable model.

• Each output shaft should be fixed by the applicable fitting. In case out-put shaft turns freely, it causes the wires to break.

• The mounting hole and stud portion of Fixture 1 are eccentric, which lets Fixture 2 slide down onto the stud of Fixture 1 to fasten the output shaft tightly.

 

Product Options:

Driver Card No. CBM-105F Driver Cards ITOH DENKI Vietnam | ITOH DENKI Việt Nam

Models Applicable

PM486FS, PM486FE, PM486FP, PM570FE,PM605FE, PM635FS

Specification Document

CBM-105F Product Sheet .pdf

Technical Document

CBM-105F Driver Card Technical Document rev13-0514

CAD Drawing Download (.DWG)

CBM-105F .DWG File

Features:

- Provides thermal protection for both Power Moller and driver card

- Two LED’s to identify type of error

- Error output signal for self diagnosis

- Dynamic brake and servo brake control

- Variable speed by rotary switch or external voltage input

- Direction control by DIP switch or external signal input

- Adjustable acceleration and deceleration time (0-2.5s)

- Switch for automatic or manual recovery of back EMF error and thermal overload device

- Forcibly stops the motor if there is a motor lock, back EMF, or thermal overload occurs

- Includes mounting hardware and wiring connector

- Two (2) M4 x 15 phillips pan head mounting screws and nuts                                        

- Connectors for power and control are:

Power: WAGO #734-102 (Included)

Control: WAGO #733-105 (Included)

Dimensions:

Specifications:

Electrical	• 24V DC ±10% input • Battery • Power Supply: fullwave rectified with smoothed current and < 10% Ripple • Power ON delay < 1s • 4A locking current • Input signal level for activation • 0V (3V or less) for NPN • 24V (18V or greater) for PNP • Output (Error and Motor Pulse) signals • Open collector 24V, 25mA or less • NPN • PNP (selectable for Error only) • Brake model only • 0.2s delay between stop signal and mechanical brake reaction • 0.2A brake current @24V (< 0.1s) • Brake coil is active (disengaging brake) while motor is running
Brake	• Dynamic (Electric-Both models) • Mechanical (CB-016BS7 only)
Protection	• Thermal protection reaction • 85° C (185° F) on the PCB • 105° C (221° F) in the motor • Built-in 5A fuse for power supply protection • Built-in diode for incorrect wiring protection
Applicable Environment	• Temperature 0~40° C (32~104° F) • < 90% Relative Humidity (No condensation) • No corrosive gas • Vibration < 0.5G
Power Source	• 24VDC Battery or 24VDC Power Supply• Battery or fullwave rectified with smoothed current < 10% Ripple

Driver Card No. CBM-103F Driver Cards ITOH DENKI Vietnam | ITOH DENKI Việt Nam

Models Applicable

PM635KE

Specification Document

CBM-103F Product Sheet .pdf

Technical Document

CBM-103F Driver Card Technical Document rev13-0514

CAD Drawing Download (.DWG)

CBM-103F DWG File

Features:

Designed for use with the high torque PM635KE (up to 10A)
Built in thermal protection for both driver card and Power Moller
Two LED’s to identify type of error and number of occurrences
Dynamic brake control
Stable speed functions to ensure articles of different weights travel at the same rate
Variable speed control with rotary switch for 10 fixed speed settings or by external voltage input for up to 16 speeds
Direction control by onboard DIP switch or external signal input
Adjustable acceleration and deceleration time (0 to 2.5s)
Switch for manual or automatic recovery of thermal overload device
Forcibly stops the motor if motor lock or thermal overload error lasts for 4 seconds or more
Induced voltage protection
Includes mounting hardware and wiring connectors
Two (2) M4 x 15 phillips pan head mounting screws and nuts
Connectors for power and control are: Power: WAGO #231-102/026-000 (Included)
Control: WAGO #733-105 (Included)

Dimensions:

Wiring:

Specifications:

Electrical	24V DC ±10% input
	-Battery
	-Power Supply: fullwave rectified, smooth current <10% Ripple
	Power ON delay < 1s
	10A locking current
	Input signals (minimum 2.2mA, maximum 7.3mA)
	-NPN (0V)
	-PNP (+24V DC)
	Output signals (open collector 24V, 25mA or less)
	-NPN (0V)
	-PNP (+24V DC; selectable for Error only)
Applicable PM Models	PM635KE
Brake	Dynamic (electric)
Protection	Motor control thermal protection
	-95°C (203°F) on the PCB
	-105°C (221°F) in the motor
	Built-in diode for incorrect wiring protection
	Built-in 18A in-line fuse for supply protection
	Built-in thermal fuse to prevent overheating
	-139°C (282°F)
Applicable Environment	Temperature 0~40° C (32~104° F)
	<90% Relative Humidity (No condensation)
	No corrosive gas
	Vibration <0.5G